Simetrics PT12
The Seametrics PT12 Pressure/Temperature Sensor has been designed to provide trouble-free submersible operation in liquid environments. This sensor communicates via SDI-12 (v1.3) or Modbus® RTU (RS485)protocol.
Pressure/level is measured with an extremely rugged and stable piezo-electric, media isolated pressure element and compensated for temperature using our proprietary calibration methodology. Temperature is measured using an on-board digital chip.
Seametrics also carries a special version of the PT12 designed to measure barometric pressure in reference to absolute pressure. If you are using an absolute PT12, contact your representative for details on how our PT12-BV can facilitate obtaining barometrically compensated pressure/level.
Application
- Rugged construction can replace analog sensors
- Monitor groundwater, well, tank, and tidal levels
- Pump testing
- Flow monitoring
Another Article: |
Specification
| Housing & Cable | Weight | 0.8 lb. (0.4 kg) | ||
| Body Material | 316 stainless or titanium | |||
| Wire Seal Material | Fluoropolymer and PTFE | |||
| Cable | Submersible: polyurethane, polyethylene, or ETFE; 4 lb./100 ft., 1.8 kg/30 m; 2000 ft max for Modbus® | |||
| Desiccant | 1-3 mm indicating silica gel | |||
| Field Connector | Available as an option | |||
| Temperature | Operating Range | Recommended: -15 ̊ to 55 ̊C (5 ̊ to 131 ̊F) Requires freeze protection kit if using pressure option in the water below freezing. | ||
| Storage Range | -40 ̊ to 80 ̊C (-40 ̊ to 176 ̊F) | |||
| Power | Voltage | 9-16Vdc, 24Vdc over voltage protection, electromagnetic & transient protection IEC-61000 – 4-3, 4-4, 4-5, 4-6 | ||
| Supply Current | Active 3mA average/ 10mA peak; sleep 150 μA | |||
| Communication | Modbus® | RS485 Modbus® RTU, output=32bit IEEE floating point | ||
| SDI-12 | SDI-12 (ver. 1.3) – ASCII | |||
| Output Channels | Temperature | Depth/Level | ||
| Element | Digital IC onboard | Silicon strain gauge transducer, 316 stainless or Hastelloy | ||
| Accuracy | ±0.5°C — 0° to 55°C (32 ̊ to 131 ̊F) ±2.0°C — below 0°C (32 ̊F) | ±0.05% FSO (typical, static) ±0.1% FSO (maximum, static) (B.F.S.L. 20 ̊C) | ||
| Resolution | 0.06 ̊C | 0.0034% FS (typical) | ||
| Units | Celsius, Fahrenheit, Kelvin | PSI, FtH₂O, inH₂O, mmH₂O, mH₂O, inH₂O, cmHg, mmHg, Bars, Bars, kPa | ||
| Range | -15 ̊ to 55 ̊C (5 ̊ to 131 ̊F) | Gauge | PSI: 1², 5, 7, 15, 30, 50, 100, 300 FtH₂O: 2.3², 12, 35, 69, 115, 231, 692 mH₂O: 0.7², 3.5, 5, 10.5, 21, 35, 70, 210 | |
| Absolute² | PSI: 30, 50, 100, 300 FtH₂O: 35, 81, 196, 658 mH₂O: 10, 24, 59, 200 | |||
| Compensated | — | 0 ̊ to 40 ̊C (32 ̊ to 104 ̊F) | ||
| Max operating pressure | 1.1 x full scale | |||
| Overpressure protection | 3x full scale up to 300psi – for > 300psi (650 ft or 200 m) contact factory | |||
| Burst pressure | 1000 psi (approx. 2000 ft or 600 m) | |||
| Environmental | IP68, NEMA 6P | |||
*Specifications subject to change. Please consult our web site for the most current data (seametrics.com). Modbus is a registered trademark of Schneider Electric.
1 Higher pressure ranges available upon request
2 ±0.25% accuracy FSO (max) at this range
3 The depth range for absolute sensors has 14.7 PSI subtracted to give actual depth allowed.
1 Higher pressure ranges available upon request
2 ±0.25% accuracy FSO (max) at this range
3 The depth range for absolute sensors has 14.7 PSI subtracted to give actual depth allowed.
For further information please contact : marketing@wmablog.com